25% Discount for payments with Crypto Currency



cumminz

Cummins X15 CM2450 X124B (2018 & Newer) Fault Code: 212 PID: PID 175 SPN: 175 FMI: 3 Engine Oil Temperature Sensor 1 Circuit- Voltage Above Normal or Shorted to High Source

Posted by PerDiezel Solutions on

Circuit DescriptionThe engine oil temperature sensor is a variable resistor sensor and is used to measure the temperature of the engine oil in the oil rifle. The engine control module (ECM) supplies 5 volts to the engine oil temperature signal circuit. The ECM monitors the change in voltage caused by changes in the resistance of the sensor to determine the engine oil temperature. When the oil temperature is cold, the sensor or thermistor resistance is high. The ECM signal voltage only pulls down a small amount through the sensor to a ground. Therefore, the ECM senses a high signal voltage...

Read more →


Cummins X15 CM2450 X124B (2018 & Newer) Fault Code: 213 PID: PID 175 SPN: 175 FMI: 4 Engine Oil Temperature Sensor 1 Circuit- Voltage Below Normal or Shorted to Low Source

Posted by PerDiezel Solutions on

Circuit DescriptionThe engine oil temperature sensor is a variable resistor sensor and is used to measure the temperature of the engine oil in the oil rifle. The engine control module (ECM) supplies 5 volts to the engine oil temperature signal circuit. The ECM monitors the change in voltage caused by changes in the resistance of the sensor to determine the engine oil temperature. When the oil temperature is cold, the sensor or thermistor resistance is high. The ECM signal voltage only pulls down a small amount through the sensor to a ground. Therefore, the ECM senses a high signal voltage...

Read more →


Cummins X15 CM2450 X124B (2018 & Newer) Fault Code: 214 PID: PID 175 SPN: 175 FMI: 0 Engine Oil Temperature- Data Valid But Above Normal Operating Range- Most Severe Level

Posted by PerDiezel Solutions on

Circuit DescriptionThe engine oil temperature sensor is a variable resistor sensor and is used to measure the temperature of the engine oil in the oil rifle. The engine control module (ECM) supplies 5 volts to the engine oil temperature signal circuit. The ECM monitors the change in voltage caused by changes in the resistance of the sensor to determine the engine oil temperature. When the oil temperature is cold, the sensor or thermistor resistance is high. The ECM signal voltage only pulls down a small amount through the sensor to a ground. Therefore, the ECM senses a high signal voltage...

Read more →


Cummins X15 CM2450 X124B (2018 & Newer) Fault Code: 2182 PID: SID 79 SPN: 1072 FMI: 3 Engine Brake Actuator Driver 1 Circuit- Voltage Above Normal or Shorted to High Source

Posted by PerDiezel Solutions on

Circuit DescriptionThe Engine Control Module (ECM) controls engine brakes on cylinders 1, 2, and 3 by sending a signal on the engine brake solenoid number 1 signal circuit. If an engine brake is installed, there will be a jumper harness from this connector to the engine brake pass-through connectors on the rocker lever housing. Component LocationThe engine brake solenoids are located under the valve cover. The engine brake solenoids are controlled through the engine harness by the ECM. Conditions for Running the DiagnosticsThis diagnostic runs when the keyswitch is in the ON position and when the pulse width modulated (PWM)...

Read more →


Cummins X15 CM2450 X124B (2018 & Newer) Fault Code: 2183 PID: SID 79 SPN: 1072 FMI: 4 Engine Brake Actuator Driver 1 Circuit- Voltage Below Normal or Shorted to Low Source

Posted by PerDiezel Solutions on

Circuit DescriptionThe Engine Control Module (ECM) controls engine brakes on cylinders 1, 2, and 3 by sending a signal on the engine brake solenoid number 1 signal circuit. If an engine brake is installed, there will be a jumper harness from this connector to the engine brake pass-through connectors on the rocker lever housing. Component LocationThe engine brake solenoids are located under the valve cover. The engine brake solenoids are controlled through the engine harness by the ECM. Conditions for Running the DiagnosticsThis diagnostic runs when the keyswitch is in the ON position and when the pulse width modulated (PWM)...

Read more →


PerDieselSolution Logo

WARNING!

PerDieselSolution informs all customers and visitors that fake websites and copied domains are being used by scammers.

Please make sure you are visiting our ONLY official website:

perdieselsolution.com

We publish this notice to protect our customers from fraudulent stores and unofficial sellers.