The ECM detects the following conditions: •The idle shutdown timer has expired and the engine has shut down. Probable Causes: 1) It code 84-08 is active, Idle Shutdown Timer will not activate2) Reprogram parameter in ECM3) Brake pedal switch/harness4) Clutch pedal switch/harness5) Vehicle speed sensor/harness6) PTO switch sensor/harness CAT 3406E (Prefix 1MM or 2WS) Fault Code: 46 PID: SPN: 100 FMI: 11 Very Low Oil Pressure CAT 3406E (Prefix 1MM or 2WS) Fault Code: 46 PID: SPN: 100 FMI: 1 Low Oil Pressure Warning CAT 3406E (Prefix 1MM or 2WS) Fault Code: 42 PID: SPN: 22 FMI: 13 Engine Speed...

The ECM detects the following conditions: •The timer for the PTO has expired and the engine has shut down. Probable Causes: 1) ECM Connection/Harness2) PTO timer programmed incorrectly3) PTO timer operated correctly and shut down as it is programmed to do4) Check engine light or PTO switch on lamp failure5) Vehicle speed circuit/sensor6) PTO switch circuit/sensor CAT 3406E (Prefix 1MM or 2WS) Fault Code: 47 PID: SPN: 71 FMI: 1 Idle Shutdown CAT 3406E (Prefix 1MM or 2WS) Fault Code: 46 PID: SPN: 100 FMI: 11 Very Low Oil Pressure CAT 3406E (Prefix 1MM or 2WS) Fault Code: 46 PID:...

This condition indicates that the battery circuit to the Engine Control Module (ECM) has a battery condition that is intermittent while the engine is running. If battery voltage disappears without returning, the ECM will not log this diagnostic code and the engine will shut down. The ECM detects the following conditions: •The ignition key switch is in the ON position.•The engine is running.•The engine is not cranking.•The ECM has been powered for at least three seconds. The ECM will detect one of the following conditions: •The battery voltage drops below 6 VDC for at least 0.50 seconds.•Three voltage readings in...

No codes, there is nothing to do. CAT 3406E (Prefix 1MM or 2WS) Fault Code: 51 PID: SPN: 168 FMI: 2 ECM Battery Power Intermittent CAT 3406E (Prefix 1MM or 2WS) Fault Code: 47 PID: SPN: 71 FMI: 14 PTO Shutdown CAT 3406E (Prefix 1MM or 2WS) Fault Code: 47 PID: SPN: 71 FMI: 1 Idle Shutdown CAT 3406E (Prefix 1MM or 2WS) Fault Code: 46 PID: SPN: 100 FMI: 11 Very Low Oil Pressure CAT 3406E (Prefix 1MM or 2WS) Fault Code: 46 PID: SPN: 100 FMI: 1 Low Oil Pressure Warning CAT 3406E (Prefix 1MM or 2WS) Fault...

This condition indicates that the “Transmission Style” parameter is programmed to the Eaton Top 2 and any one of the following parameters are not programmed: •”Auxiliary Output 2″ (Multi-Function Output #2) is not programmed to “Shift Solenoid”.•”Auxiliary Output 3″ (Multi-Function Output #3) is not programmed to “Lockout Solenoid”.•”Gear Ratios” not programmed Probable Causes: Program the “Transmission Style” parameter that is Eaton Top 2 to the correct setting. If an Eaton Top 2 Transmission is not used, program the correct “Transmission Style” parameter to the correct setting. CAT 3406E (Prefix 1MM or 2WS) Fault Code: 56 PID: SPN: 253 FMI: 2...